General

How to Setup Private Internet Access Routers in 2023

3 Mins read

Private Internet Access is one of the biggest brands in the VPN industry. Although the VPN is compatible with a lot of platforms and devices, there is no dedicated app or client for routers. Instead, you will have to configure the VPN manually on your router.

In this article, I’m going to explain how to setup PIA on routers.

If you want to learn about this VPN in greater detail, see this Private Internet Access review.

Setup Instructions for Private Internet Access on Routers

PIA is compatible with a few brands of routers. However, it is most amenable for configuration if you have a DD-WRT interface. In this article, I’ll walk you through the installation steps for DD-WRT, which is the more widely used firmware.

DD-WRT Setup

Here’s what you need to do to setup PIA on DD-WRT.

Step 1: Subscribe to PIA.

Step 2: Open your DD-WRT admin interface and navigate to ‘Setup’ > ‘Basic Setup’.

Step 3: Enter PIA DNS servers in the static DNS fields as follows:

  • Static DNS 1 = 209.222.18.222
  • Static DNS 2 = 209.222.18.218

Step 4: Now move to Network Address Server Settings (DHCP) and ensure the following:

  • Use DNSMasq for DHCP = Checked
  • Use DNSMasq for DNS = Checked
  • DHCP-Authoritative = Checked

Step 5: Save and Apply Settings.

Step 6: Now click on ‘Setup’  tab and click on ‘IPV6’.

Step 7: Set IPv6 to ‘Disable’, save and apply settings.

Step 8: Move to Services.

Step 9: Remove the DNS Suffix (if any).

Step 10: Under DHCP Server, Set Used Domain to ‘LAN & WLAN’.

Step 11: Under DNSMasq make sure the following are true:

  • DNSMasq : Enabled
  • Local DNS : Enabled
  • No DNS Rebind : Enabled

Step 12: Save and Apply Settings.

Step 13: Move to ‘Service’ > ‘VPN’.

Step 14: Under OpenVPN Client, click Enable on Start OpenVPN Client to see more options.

Step 15: Click ‘Enable’ on Advanced Options and more options will appear.

Step 16: Now enter:

  • Server IP/Name = us-west.privateinternetaccess.com [*]

Or if you prefer to use a specific location, You can find the full list of locations here: https://www.privateinternetaccess.com/pages/network

  • Port = 1198
  • Tunnel Device = TUN
  • Tunnel Protocol = UDP
  • Encryption Cipher = AES­-128-­CBC
  • Hash Algorithm = SHA1
  • User Pass Authentication = Enable
  • Username, Password = Your PIA username & password
  • TLS Cipher = None
  • LZO Compression = Yes
  • NAT = Enable

Step 17: Type the following information in Additional Config:

  • persist-key
  • persist-tun
  • tls-client
  • remote-cert-tls server

Step 18: Download this file https://www.privateinternetaccess.com/openvpn/ca.rsa.2048.crt

Step 19: Once downloaded, right-click the ca.rsa.2048 file, then click Open With > Notepad.

Step 20: Select all the contents of the file by pressing ‘Ctrl + A’, then press Ctrl + C.

Step 21: Find the CA Cert field and paste the copied contents of the file by pressing ‘Ctrl’ + ‘V’. Be sure the entire text from “—–BEGIN CERTIFICATE—–“ and “—–END CERTIFICATE—–” is pasted.

Step 22: Save and Apply Settings.

Step 23: To check if the VPN is now active, click on ‘Status’ > ‘OpenVPN’. When connected, you will see the message “Client: CONNECTED SUCCESS”

PIA Compatible Routers

Unfortunately, you cannot just make PIA work with every router. Instead, you need routers that let you configure a VPN service.

Following are three different router types that support Private Internet Access.

Flash Routers Combined with New Firmware

The term flashing refers to installing a new firmware in your router. These firmware work as an Operating System within your router and they end up determining its capabilities.

For a router to support VPN such PIA, it need firmware like DD-WRT or Tomato.

  • DD-WRT is compatible with more routers as compared to Tomato. It lets you adjust the extent of the Wi-Fi signal and prioritize the online traffic.
  • Tomato allows you to run two VPN servers simultaneously. It is also more user-friendly and has more bandwidth monitoring options than DD-WRT.

OpenVPN Compatible Routers

Some routers support OpenVPN protocol thus allowing you to use any VPN that operates on the Open Source technology.

Since PIA uses OpenVPN, this device works perfectly as a Private Internet Access router. Moreover, with this router at your disposal, you do not need to flash new firmware.

Pre-Flashed Routers

The process of manually setting up VPNs on routers can be a bit taxing. Luckily, pre-flashed routers exist to save us from the hassle. These routers come with pre-installed VPNs like Private Internet Access.

Although these routers are somewhat expensive, they provide several perks to that make them worth it.

Conclusion

With mass surveillance and cybercrimes at their peak, users have no other choice but to encrypt their online activities. The malicious entities on the internet are always upgrading their nefarious designs. Users should follow suit and protect themselves on all devices by learning how to setup Private Internet Access on router.

Related posts
GeneralTechnology

Hands On with the Samsung Galaxy Z Flip

Samsung’s second foldable phone takes a different approach: instead of folding larger, it folds smaller, much like Motorola’s new razr foldable. It’s…
GeneralTechnology

Download SHAREit APK for Android, iOS and PC

SHAREit is the most popular cross-platform file sharing app that allows you to share any and every kind of file with other…
GeneralTechnology

How To Get Apple TV+ For Free

Apple TV+ the streaming service from Apple is finally here. It will cost £4.99/$4.99 a month, which is less than other streaming…
Get Latest Updates On Technology

We respect your privacy!

Leave a Reply

Your email address will not be published.